Shop Now ›

Neoprene

PRODUCT INFORMATION

Grade 1 = Styrene Butadiene Rubber (SBR)

Grade 2 = Chloroprene Rubber (CR)

Laminated with 100% Nylon Jersey

See Test Reports, below

COMPOSITION INFORMATION/INGREDIENTS

Hazardous components:

This product contains no substance classified as hazardous to health. No latex polymers.

HAZARDS IDENTIFICATION

NONE

FIRST AID MEASURES

NONE: Material is not hazardous

FIRE-FIGHTING MEASURES

Suitable extinguishing media:

Foam, Water spray, Dry powder, Carbon dioxide (CO₂, Dry sand

Extinguishing media which must no be used for safety reasons:

None

ACCIDENTAL RELEASE MEASURES

Environmental precautions:

No special environmental precautions required.

Method for cleaning up:

Collect in suitable container for disposal.

STORAGE AND HANDLING

Storage:

Store in well-ventilated area away from fire.

Handling:

No smoking while handling product.

EXPOSURE CONTROLS/PERSONAL PROTECTION

Engineering measures to reduce exposure:

Ensure adequate ventilation, especially in confined areas. General industrial hygiene practice.

Respiratory protection:

No special respiratory protective equipment normally required.

Hand protection:

None

Eye protection:

None

PHYSICAL AND CHEMICAL PROPERTIES

Form:

Solid

Flash point Decomposition:

> 500°F

Odor:

Very faint

Temperature:

> 400°F

Color:

Black or Ivory

STABILITY AND REACTIVITY

Stability:

Stable at normal conditions.

Conditions to avoid:

Do not expose to temperatures over 400°F and no smoking in storage and work areas.

Hazardous decomposition products:

Thermal decomposition can lead to release of irritating gases and vapors.

TOXICLOGICAL INFORMATION

ECOTOXICITY:

NONE

DISPOSAL CONSIDERATIONS

Waste from residues:

Can be disposed as a solid waste.

Unused products:

Pack in box or bag and take to local recycling or waste disposal.

TRANSPORT INFORMATION

Not classified as dangerous in regards to transport regulations.

TEST REPORTS

1. CR/CS/SBR Comparison Charts

Property / Article CR CS SBR
Elongation, Break (%) (min) 400 350 300
Tensile Strength (kg/sg. cm) (min) 7.0 5.0 5.0
Tear Strength (kg/sg. cm) (min) 2 2 2
Hardness (Type C) 4–6 degrees 4–6/6–8 degrees 6–8 degrees
Density (G/cubic cm.) 0.18–0.2 0.16–0.18 0.2+/-0.02
Modulus at 200% Elongation (kg/sq. cm.) 2–3 2–3 4–5
Water Absortion By Weight (%) (max) 1 1 1
Shrinkage (70 degrees C., 24hrs.) (max) 2 2 2
Compression Set (Compressed 50%, 25 degrees C) 15–25 15–25 15–25

SBR / CR Comparison Chart

2. 100% CR Federal Motor Vehicles Safety Standard (FMVSS) 302 Certification.

SGS Test Results

3. Health, environmental protection, nuclear safety for food, agriculture, forestry. Soluble lead content.

Inchcape Test Report page 1

Inchcape Test Report page 2

DISCLAIMER

The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of handling and use are beyond our control, we make no guarantee of results and assume no liability for damages incurred by the use of this material. All materials may present unknown health hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Final determination of suitability of this material is the sole responsibility of the user. No representations or warranties, either expressed or implied, of merchantability, fitness for a particular purpose or any other nature are made hereafter with respects to the information contained herein or the material to which the information refers. It is the responsibility of the user to comply with all applicable federal, state, and local laws and regulations.